three Quick Do-it-yourself FLOATING Image FRAMES AND HOW TO Lower PLEXIGLASS
This write-up about how to make 3 Quick Diy Floating Image Frames And How to Lower Plexiglass is sponsored by The Home Depot as element of the #THDProSpective System. It also incorporates affiliate one-way links. See policies.
Quick Do it yourself photograph frames are essentially a single of my most asked for tutorials and oddly sufficient, till now, I didn&rsquot have a lot of to share!
.
I actually crafted my father a massive Diy tailor made picture frame as a Christmas gift a few a long time back and shared the tutorial for it in this article. But it made use of dowels, and a router, and it may have been a minimal much more associated than most men and women are searching for.
So, in this put up, I&rsquom going to show you how I made three various design and style Tremendous Quick Do it yourself floating picture frames with just two fundamental equipment. I&rsquoll also present you how simple it is to reduce plexiglass for them, too!
.
So if you&rsquore ready to get building, allow&rsquos go! I&rsquove got the movie tutorial here and the phase by stage under:
Applications AND Components:
- Miter observed (or any wooden slicing observed is good&ndashdoesn&rsquot have to be a MITER saw)
- Nail Gun (optional, just would make items a lot quicker)
- Wooden Glue
- ¾&Prime sq. dowels
- 1×2 boards
- ¼&Primary x 1 ⅛&Prime lattice trim
- Slender Plexiglass Sheets
- Ryobi A person+ HP Lower Off Tool (utilized to slice plexiglass)
- Clamps (also optional&ndashif you don&rsquot have clamps, you can use CA glue or painters tape in area of clamps to keep pieces whilst wooden glue dries)
- Change buttons
A Observe About FLOATING Photograph Frames:
I&rsquom sharing how to make three distinct style FLOATING picture frames in this tutorial, but the initially move to producing any of them is reducing the plexiglass to the size you want.
.
If you don&rsquot want to use plexiglass for your frames, you can skip this action. But given that the graphics/images I framed are &ldquofloating&rdquo within the frame, they&rsquore generally sandwiched involving two items of plexiglass. So plexiglass/acrylic is essential to be ready to &ldquofloat&rdquo your picture.
.
To make items straightforward to transform out in these frames, I also employed these transform buttons&mdashor I call them twisty tabs&ndashon the back to keep the plexiglass in location.  
HOW TO Slash PLEXIGLASS
Generally, I have my nearby glass store slash my glass and plexiglass parts for my projects.  But due to the fact these plexiglass parts will be compact and several custom made dimensions, it would be much more affordable, a lot quicker and less difficult to just reduce them myself.
.
I used some (about) ⅛&rdquo acrylic sheets from Property Depot.  They occur in various measurements, all the way up to a four×8 sheet.  I just grabbed some 11x14s.
I intended some basic graphics on my computer (PicMonkey and Canva are good for this!) and also applied a patch that I received a couple years back at a meeting for these frames.  You can use a photograph, a poster, material, regardless of what you want to frame for this.
.
I laid them out on my sheet how I preferred the spacing, then marked where by I preferred to cut&ndashno measurements right here&hellipjust eyeballing how I assumed the spacing all around the impression seemed superior.
Now, I&rsquove utilised the low-priced little hand knife they claim will lower plexiglass prior to and it was a horrible encounter with extremely weak effects.  I&rsquove also utilised a jig noticed to reduce plexiglass and it melts, receives stuck, then chips or cracks the sheet.
.
So THIS time, I attempted this new Ryobi One+ HP Compact Slash Off Tool with a plastic cutting blade and was extensively impressed with how brief and clean up the cuts had been.
When I 1st observed this software, I located it kind of unusual hunting.  But soon after I made use of it, I comprehended the notion. 
.
It&rsquos generally a hybrid among a drill and an angle grinder. It cuts like an angle grinder, but it feels a drill with the head turned ninety levels. 
.
It&rsquos compact and lightweight and it&rsquos received a forward and reverse change to flip the blade each instructions.  It&rsquos also bought a variable pace result in&mdashwhich is fantastic for chopping plastic to assist avert melting. 
It comes with a plastic and drywall blade, a steel reduce off wheel, and a diamond blade for chopping tile and cement board.  You can study far more about the new Ryboi 1+ HP lower off tool at the website link in this article if you&rsquore interested.
.
For chopping straight lines on the plexiglass, I just lined up a straight edge (scrap piece of wood), clamped and ran the metal blade guard in opposition to it to make the cut.  You can skip the straight edge and freehand these cuts, way too if you have a continual hand. (I don&rsquot haha!)
I did discover it slice most effective in this case with the change in reverse. It appeared to not melt that way.
.
I lower two parts similar in size for each merchandise I was framing. Then, I was completely ready to start making the precise floating picture frames.
Simple Diy FLOATING Picture Body Style one
Model one is my own favorite, so I&rsquoll begin with it 😊
This specific floating photo frame design and style requires ¾&Prime sq. dowels and one×2 board. It is basically just a one×2 wrapped all around a square dowel body.
.
I used ¾&rdquo sq. dowels for this and established up my miter observed to cut 45 levels.  Now, you don&rsquot have to miter these.  important source can leave it on 90 and make butt joints.  You also don&rsquot have to have a MITER noticed for this.  Any saw that you can slice fairly straight with will do the job great.
.
I fundamentally trimmed four items of sq. dowel so that when suit jointly, they&rsquod be just hardly (like ⅛&Key) bigger than the plexiglass piece I was placing in it.
I utilized wood glue to the corners and nailed them collectively with brad nails.  If you are affected individual, and don&rsquot have a nail gun, basically glue and clamp right until dry.
.
Soon after the glue experienced dried, I slice to fit one×2 items with 45 degree mitered corners around this body.  Once more, butt joints are wonderful here if you want to skip the mitered corners.
.
I glued and nailed these 1x2s close to the edges leaving about ¼&rdquo sticking out the back again side of the plexiglass, so that when I put in the two ⅛&Prime plexiglass parts, it&rsquoll be flush across the again facet of the body.
Then, I screwed these twisty tabs into the back again sides of the frame to hold the plexiglass in position.  I&rsquoll go back and cleanse the sawdust off the plexiglass later, but for now, I set this off to the aspect to make the subsequent frame.
Quick Do it yourself FLOATING Photo FRAMES Type 2
Type 2 is a minimal less difficult and is designed of 1x2s and ¼&rdquo thick by 1 ⅛&Key broad lattice trim.
I commenced by chopping down the lattice items so it would make a body that the plexiglass would healthy Inside.  All over again, just like just before, the mitered corners are optional.
As soon as I experienced this lattice frame minimize, I calculated its general sizing and slice one×2 parts to make a body whose total dimension matched that of the lattice body. See down below one×2 body laying on top of lattice frame&ndashthey&rsquore the identical size.
I glued and nailed the one×2 body collectively and clamped until eventually dry. Again, you can use tremendous glue or painters tape if you don&rsquot have a nail gun or clamps 🙂
.
Then, I flipped it upside down and glued the lattice body onto the back again.  I made use of a large object to hold it in place until eventually it was dry, then, I screwed twisty tabs on the back to keep the plexiglass in location. 
Because the lattice is ¼&rdquo thick, and the plexiglass is ⅛&rdquo thick, when the two plexiglass items are put within, all the things ought to sit flush throughout the back again just like the final frame.
Yet again, I&rsquoll go back again and thoroughly clean the sawdust off later on, but for now, I moved on to the past model frame.
Quick Diy FLOATING Picture Body Design 3
Model three is the similar idea as model one, but as an alternative of utilizing 1x2s, I applied ¼&Primary x 1 ⅛&Prime lattice trim to hold the frame a little thinner and much more minimalist looking.
So, I cut ¾&rdquo sq. dowels to make a frame the very same size or slightly larger than the plexiglass I was framing and glued and nailed it alongside one another.
Then, I reduce lattice trim to wrap all over that body. 
I glued the lattice trim on so that there was about ¼&rdquo sticking off the back facet of the sq. dowel body so that when the two pieces of ⅛&rdquo plexiglass are mounted, it&rsquoll all be flush throughout the back again.
.
I didn&rsquot have any brad nails limited more than enough to nail this frame on, so I merely glued and clamped right up until it was dry.
If you don&rsquot have clamps, you can use painters tape to variety of wrap about the items to keep until the glue dries OR basically use some tremendous glue or CA glue to help keep parts in put until the actual wood glue is cured.
.
Then, just like the last two frames, I installed twisty tabs to keep the plexiglass in area.
FLOATING Photograph Frame HANGING Choices
The final action is clear up and hanging.  I utilised some glass cleaner to clear up all the saw dust, then used a piece of double sided tape on the again plexiglass piece to make positive the photographs remain in spot, then place the frames back again with each other.
.
To dangle, you can use your standard sawtooth hangers for this.
Or merely spot it on a shelf.
.
OR, use a drill to drill holes into the corners to operate some paracord and dangle it on a piece of wooden dowel you screwed into the wall.
As you can see, earning picture frames doesn&rsquot have to be sophisticated.  This is a excellent rookie undertaking you can tackle with minimal resources and get as artistic as you want. 
.
I in fact hung these graphics up in my desk spot to help continue to keep me enthusiastic when functioning alone from household correct now. So, now that my desk place is full, I guess I must likely get back to work 😊
I hope you&rsquove relished this very little job.  There are lots additional coming your way, so be confident to subscribe to my newsletter beneath so you don&rsquot pass up out on what&rsquos coming subsequent!
.
And don&rsquot neglect to pin this for later!
Till upcoming time, happy creating 😊